The size of the nozzle opening is another influencing factor for the amount of discharge. The larger the opening, the lower the resistance the adhesive has to overcome, and thus the higher the discharge amount.
Austragsmenge bei verschieden großen Düsenöffnungen
BEAD VOLUME (310 ML CARTRIDGE)
Bead diameter 1.6 mm → Bead length 154.15 m
Bead diameter 2.4 mm → Caterpillar length 68.52 m
Bead diameter 3.2 mm → Caterpillar length 38.54 m Caterpillar Bead diameter 4.8 mm → Caterpillar length 17.13 m
Raupenvolumen
Punktvolumen
One of the most important variables when dispensing an adhesive or sealant is the correct nozzle for the required application. Especially to ensure precise repeatability, the use of a pre-cut nozzle is recommended. The user's own cutting is usually not precise enough to achieve reliable repeatability.
In addition, the choice of nozzle should be tailored to the application. For example, there are special V-joint nozzles for inserting windows in vehicle construction, many variants of slot nozzles for surface application, extra-long nozzles for applying to hard-to-reach areas, and rotating nozzles to enable adhesive application on angled surfaces. Metal nozzles are primarily used for applying hot melt adhesives and for coating rough surfaces.
The use of such special nozzles alone can achieve a significant increase in efficiency. For example, wide-application nozzles up to 40cm wide are used when laying parquet floors. The user therefore needs much less time to apply the adhesive.
For micro-dosing from standard cartridges, there are also closed nozzles that can be opened to the required diameter using a heated needle. With the correct nozzle opening, it is also possible to optimize the dispensing amount and direct it to where the adhesive is needed. This also prevents waste.
Verschiedene Düsenöffnungen
With V-notch nozzles, triangular beads are applied, which optimally adapt to the foot part tolerances.
Artikelnr.: ITR1643 | Maße B x H: 8 x 10 mm
Artikelnr.: ITR1148 | Maße B x H: 8 x 10 mm
Artikelnr.: ITR1135 | Maße B x H: 8 x 15 mm
Artikelnr.: ITR1147 | Maße B x H: 8 x 10 mm
Artikelnr.: ITR1956 | Maße B x H: 6 x 14 mm, 6 x 16 mm, 6 x 18 mm, 6 x 20mm
Artikelnr.: ITR2275 | Maße B x H: 10 x 8 mm
Artikelnr.: ITR1642 | Maße B x H: 8 x 10 mm
Artikelnr.: ITR1398 | Maße B x H: 10 x 10 mm
Artikelnr.: ITR1399 | Maße B x H: 10 x 10 mm
Artikelnr.: ITR2274 | Maße B x H: 10 x 8 mm
Artikelnr.: ITR2274 | Maße B x H: 10 x 9 mm
Artikelnr.: ITR1631 | Maße B x H: 7 x 12 mm
Artikelnr.: ITR1639 | Maße B x H: 8 x 14 mm
Artikelnr.: ITR1640 | Maße B x H: 8 x 10 mm
Artikelnr.: ITR1957 | M15 mit Anstecher, passt zu allen M15-Düsen
Artikelnr.: ITR1154 | M15, passt zu allen M15-Düsen
Artikelnr.: ITR1635 | S15 mit Anstecher, passt zu ITR1398 und ITR1399
Artikelnr.: ITR1155 | M20, passt zu ITR16343
For surface bonding, such as when laying wooden floors, the use of special flat and surface nozzles is recommended. The adhesive user does not need to lay individual beads, trowel, or spread the adhesive, thus saving valuable working time. In addition, the use of flat and surface nozzles achieves a more uniform layer thickness, making the adhesive application more precise, safer, and reproducible.
Here you can see the diverse selection of flat and wide-angle nozzles that we have found for you worldwide and included in our range.
We are happy to develop your very special solution with you, from the design to the finished injection-molded part.
Contact us!
Grobgewinde (S15) | Artikelnr.: ITR2276 | Maße B x H: 2x 10 mm
Feingewinde (M15) | Artikelnr.: ITR2277 | Maße B x H: 2 x 10 mm
Grobgewinde (S15) | Artikelnr.: ITR1641 | Maße B x H: 2,5 x 10,8 mm
Feingewinde (M15) | Artikelnr: ITR2279 | Maße B x H: 2 x 20 mm
Grobgewinde (S15) | Artikelnr.: ITR2278 | Maße B x H: 2 x 20 mm
Grobgewinde (S15) | Artikelnr.: ITR1958 | Maße B x H: 2,5 x 20 mm
Bördelnahtdüse Feingewinde (M15) | Artikelnr.: ITR1644 | Maße B x H: 6 x 15 mm
Bördelnahtdüse Feingewinde (M15) | Artikelnr.: ITR1390 | Maße B x H: Zuschneidbar 2 x 6 – 13 mm
Feingewinde (M15) | Artikelnr.: ITR1210 | Maße B x H: 2,2 x 30 mm
Grobgewinde (S15) | Artikelnr.: ITR1566 | Maße B x H: 2,2 x 30 mm
Grobgewinde (S15) | Artikelnr.: ITR1945 | Maße B x H: Zuschneidbar 2 x 20-40 mm
Grobgewinde (S15) | Artikelnr.: ITR1971 | Maße: 78 mm Breite 4 mm Raupendurchmesser mit Führungsdorn
Grobgewinde (S15) | Artikelnr.: ITR1909 | Maße: 80 mm Breite, 3,8 mm Raupendurchmesser
Feingewinde (M15) | Artikelnr.: ITR2225 | Maße: 148 mm Breite 4 mm Raupendurchmesser
Feingewinde (M15) | Artikelnr.: ITR2224 | Maße: 298 mm Breite 4 mm Raupendurchmesser
Folienbeuteldüse | Artikelnr.: 7XS111 | Maße: 190 mm Breite 3 mm Raupendurchmesser
Note: Coarse thread S15 fits plastic cartridges; Fine thread M15 fits aluminum cartridges. We offer adapters from S15 to M15 and vise versa (ITR2254 and ITR2255).
Individual partners and customers require individual solutions. Thru 3D printing technology, nozzles can be individually manufactured to meet the user's specific needs. To create an optimal solution, the adhesive process is first analyzed. Subsequently, a suitable nozzle is conceived and designed. This opens up entirely new processing possibilities for adhesive users.
Feel free to contact us. We implement all ideas with you and our partners. We conduct tests in our facilities to optimize the nozzle and find the most suitable discharge device. In addition, a video documentation is being created.
So that we can better prepare for the conversation with you, you can let us know your price expectations in advance.
Enter your price for the selected quantity in the field desired price.
We will then check whether we can meet your desired price or advise you on alternative products that better meet your price expectations.
PRODUCT TITLE